CALCULATE WITH CONFIDENCE

Trades & Professional Tools · Flooring & Tile

Carpet Stair Runner Calculator

Plan broadloom runner cut length and roll-width yield from separate tread/riser counts, relevant face dimensions, landings, repeat and flight count.

Trades & Professional Tools · Flooring & Tile

Enter your project measurements

Measured inputs · visitor-entered product and design assumptions
  1. 1EnterProvide the known values
  2. 2CalculateResults update automatically
  3. 3VerifyReview the details and units
Try an example

Measure using one consistent system. Product coverage, density, resistance, waste, and safety assumptions must come from the actual product data or project specification. Values stay in this browser.

Trade calculator result

—

Enter valid values to see the result.

Your entries are calculated in this browser and are not submitted to 365CALCS.COM.

Feedback

Understand the job

What the Carpet Stair Runner is for

Plan broadloom runner cut length and roll-width yield from separate tread/riser counts, relevant face dimensions, landings, repeat and flight count.

Carpet planning is governed by roll direction, seams, pattern matching, stairs, tile modules, and usable offcuts as well as area.

Simple visual explanation

Follow the calculation from field input to decision

Measure rooms and stairs
Plan roll or tile layout
Total material and seams
Each stage is deliberately separate: verify the source values, the calculation basis, and the final field or shop check.
Covered tread countCovered riser countCovered tread going (mm or in)Covered riser height (mm or in)Additional landing/turn length (m or ft)

The relationship

Read the formula before using the result

Raw runner length=treads×going+risers×rise+landing; matched length rounds to repeat; lanes uses a ULP-safe whole-ratio floor of roll width÷runner width.

The calculator preserves full internal precision. Confirm that every entry uses the same measurement condition, unit basis, product or machine data, and scope represented by this formula.

Professional check

Turn the answer into a responsible next step

1. Verify the inputs

Use actual measurements, current drawings, approved specifications, and manufacturer or process data for the real job.

2. Challenge the assumptions

Check allowances, losses, stock or package rounding, operating condition, and whether the result matches an independent measurement or estimate.

3. Respect the boundary

It does not approve substrates, moisture conditions, waterproofing, movement joints, adhesives, heated floors, stairs, transitions, slip resistance, or an installation system.

Quick guide

How to use this calculator

  1. Choose the calculation mode or measurement system that matches the values you actually have.
  2. Enter measured project dimensions and use product-specific coverage, density, yield, resistance, or waste data where requested.
  3. Review the intermediate results before ordering material or applying the result on site.

Calculation method

Calculation method

Raw runner length=treads×going+risers×rise+landing; matched length rounds to repeat; lanes uses a ULP-safe whole-ratio floor of roll width÷runner width.

The calculator preserves full internal precision and rounds only displayed results. Quantity outputs round up when whole purchasable pieces are required.

Worked example

Worked example

Nine 280 mm treads and ten 175 mm risers need 4.27 m of runner before landing and repeat allowance.

Raw runner length=treads×going+risers×rise+landing; matched length rounds to repeat; lanes uses a ULP-safe whole-ratio floor of roll width÷runner width.

Supported inputs

Precision and limits

Flooring-system and substrate boundary

These tools use measured geometry, product dimensions, package coverage, layout conventions, field rates, test readings and approved comparison limits you enter. They do not select or approve a tile, flooring, adhesive, grout, underlayment, waterproofing, movement-joint, heated-floor, moisture, substrate, stair, seam, transition, fire, acoustic, slip-resistance or electrical system.

Planning scope

This calculator supports measurement, estimating, and scenario planning. It does not inspect a site, select a product, certify a design, or replace drawings, specifications, manufacturer instructions, local codes, permits, or a qualified trade professional.

Measured and product-specific inputs

Nominal dimensions can differ from actual dimensions. Verify inside pipe diameters, actual lumber sizes, product coverage, bag yield, material density, conductor resistance, waste, and packaging against the materials used on the project.

Safety and regulatory limits

Electrical, HVAC, structural, excavation, roofing, pressure, lifting, and life-safety work may require jurisdiction-specific calculations and professional approval. Do not use a generic planning result as a code-compliance or safety determination.

Precision and privacy

Inputs accept bounded plain decimals. Calculations remain in this browser and raw entered project values are not submitted to 365CALCS.COM.

Continue calculating

Related calculators